ELM Video Technology, Inc.
DMX
0~10 Volt Converter
/ Switch / Relay Driver
PCB
enlarge
8 Channel
12 Channel
16 Channel
DMX10V
16 Channel
side view
*4 Channel
Sub PC Board
*Back View
Alternate
Mounting
Style
The DMX10V is a DMX to 10 Volt Converter,
and can be used as a switch that could drive Solid State Relay's. Each output is assigned
to a consecutive DMX channel and will vary from 0
to 10V in respect to the corresponding DMX channels' level.
Usage examples include: trigger/control devices up to 10V,
rapid switch equipment or lights, or control water fountain
solenoids or SSR's (Solid State Relays). The Start Channel is assigned by dip switches 1 ~ 9,
DMX512 CHANNEL ASSIGNMENT TABLE
[PDF].
For example if the DMX start channel is assigned to 10, and
the level on channel 10 is 127, then the 1st output will be
+5 volts, level of 0 = 0 volts, and a level of 255 = 10 volts etc.). Each output will
source 20mA. The variable output can drive 10V dimmers
(insure your dimmers operate within these specifications,
overdriving may cause failure).
The DMX10V is also equipped with a Switch
output mode, at a specific threshold the outputs will either
switch fully ON or OFF. Great for controlling Solid State
Relays (SSR).
*Add a 4 Ch Sub PCB to an existing 4, 8, or 12 channel PCB.
**The alternate back mounting option allows the PCB to be mounted in an enclosure with DIP
Switch and LED's accessible externally of the enclosure. For installations that need top
(or internal) DIP Switch and LED accessibility then these items can be mounted on the top of the PCB.
FEATURES:
- Engineered with quality parts and a reliable and simple design
- Data LED illuminates indicating DMX 512 signal is present, and a Power LED for +12VDC
- Could use 5 pin or 3 pin XLR's or combination of either for the DMX input
- Expandable - For 4 or 8 output PCB's, Add up to (2) DMX10VSUB PCB's to increase the outputs X's 4 each.
- Assign the address start channel to any of the 512 DMX channels
- Auto Reset Fuse
PCB INCLUDES:
- Preassembled DMX10V-PCB (Printed Circuit Board) with (4) .5" standoffs and screws for enclosure mounting
- Enclosure Labels ( Download replacement ENCLOSURE LABELS )
- Download - DMX10V USER GUIDE [PDF]
- Download - DMX10V DRILL TEMPLATE AND WIRING DIAGRAM [PDF] for Neutrik 3/5 pin M/F XLR's
- Download - DMX512 CHANNEL ASSIGNMENT TABLE
Specifications:
- Dimensions: 1.3" Length x 3.4" Width x 1" Height (including standoffs)
- Power Input: +12VDC apx 400mA (values apx,
some circuits may vary)
4 Channel: no load:64mA full load 145mA
8 Channel: no load 70mA full load 230mA
12 Channel: no load 76mA full load 316mA
16 Channel: no load 82mA full load 402mA
subtract 19mA if no DMX is present - Voltage Output: 0~10VDC at 20mA Max each, (500 ohm load)
- Data Input: DMX512
- Fuse: Auto Reset [750mA]
- Item model number: DMX10V-PCB4, DMX10V-PCB8, DMX10V-PCB12, or DMX10V-PCB16
- Refresh Rate Per Second: 4 Ch's = 1162, 8 Ch's =
571, 12 Ch's = 384, 16 Ch's = 285
(amount of times per second the outputs are updated)
Please note: Ships with the DIP Switch, LED's, and sub PC boards unsoldered for custom enclosure mounting options.
Upon request these items can be mounted
at no additional cost - may delay shipping time.
Please Note: DIP Switch color and style may vary.
DMX Dual SSR Relay
DMX PWM / Dimmer / Control PC Board
DMX Coil Relay Driver PCB
Made in the USA
