• DMX CONTROL WARNING: NEVER use DMX data devices where human safety must be maintained.
  • NEVER use DMX data devices for pyrotechnics or similar controls.
  • Manufacturer: ELM Video Technology
  • Brand: ELM Video Technology
  • Model: DX10V-PCB
  • Name: DMX to 0-10 Volt Analog Converter Switch Relay Driver
  • MPN: DX10V-4-PCB
  • UL Listings: PCB pre populated
  • Dimensions: 1.3" Length x 3.4" Width x .6" Height (including standoffs)
  • Condition: New
  • PCB Mounted Fuse: SMT 750mA
  • Power Input: +12VDC apx 400mA (values apx, some circuits may vary)
  •     4 Channel:   no load:64mA   full load 145mA
  • Voltage Output: 0~10VDC each, (500 ohm minimum load)
  • Source Current Output: 20mA Max
  • Sink Current Output: 10mA Max
  • DATA TYPE: DMX (250Khz)
  • Weight: 2 oz
  • Operating temperature: 32°F to 85°F
  • Storage temperature: 0°F to 120°F
  • Humidity: Noncondensing



PCB Selectable features:
  • (3) 12VDC Power Supply (will power up to 2 PCB's)
  • 5" Wire Leads - 5" Wire leads are factory installed for all 5 PCB's
  • (5 sets) DIN Rail Clips
  • (3) DIN Rail 8" ( will mount 5 PCB's)
  • Screw Terminals Omitted - If mounting the PCB on a faceplate with the LEDs and DIP switch accessible from the front of the enclosure, the screw terminals can be omitted and the wires soldered directly to the board to allow the pcb to mount flush.
  • Mount Screw Terminals on Back of PCB - If mounting the PCB on a faceplate with the LEDs and DIP switch accessible from the front of the enclosure, the screw terminals can be mounted on the back of the board to allow the pcb to mount flush


Lot of 5 custom 4 channel PCBs. The DX10V-PCB converts a DMX-512 input to a variable 0 to 10 volt analog output. Control 0-10 volt LED drivers or dimmers, for example, from a DMX lighting board or DMX controller. Also has a 'switch' option for controlling solid state relay's (SSR). Each output can source up to 20mA and sink up to 10mA. Each output is assigned to a consecutive DMX channel and will vary from 0 to 10 volts in respect to the corresponding DMX channels' level. See the DX10V 0-10 volt full description category page for more information. 

The DX10V-PCB is designed to mounted for access to the dip switches and LED's either internal or external of an enclosure. The standoffs are mounted on the bottom of the PCB for installing in an enclosure. If the dip switches and LED's are to be accessible from the exterior of the enclosure then simply move the standoffs to the top of the PCB and mount face out of the enclosure.

FEATURES:

  • Engineered with quality parts and a reliable and simple design
  • Screw terminals installed for easy connection
  • 4 Independent 10 Volt Outputs
  • Data LED illuminates indicating DMX 512 signal is present, and a Power LED for +12VDC
  • Switch mode to drive solid state relays
  • Assign the address start channel to any of the 512 DMX channels
  • Stand-alone (DMX off) optionally will turn all outputs on or off

PCB INCLUDES:

  • Preassembled DMX10V-PCB (Printed Circuit Board) with (4) .25" standoffs and screws for enclosure mounting

DMX (4) Ch 0-10 Volt Analog Converter PCB Lot of 5

  • $585.00


  • 2 or more $1,099.00

Available Options


Related Products

DMX 0-10 Volt Analog Converter DIN Rail / Wall Mount

DMX 0-10 Volt Analog Converter DIN Rail / Wall Mount

The DX10V-DIN converts a DMX-512 input to a variable 0 to 10 volt analog output in a 24 or 32 termin..

$259.00

DMX 0-10 Volt Analog Converter

DMX 0-10 Volt Analog Converter

The DX10V converts/decodes a DMX-512 input to a variable 0 to 10 volt analog output. Control 0-10 vo..

$289.00

DMX 0-10 Volt Analog Converter PCB

DMX 0-10 Volt Analog Converter PCB

The DX10V-PCB converts a DMX-512 input to a variable 0 to 10 volt analog output. Control 0-10 volt L..

$145.00

DMX 0 to -20 Volt Analog Converter PCB

DMX 0 to -20 Volt Analog Converter PCB

The VC-20 PCB interfaces with the DX10V-PCB (converts DMX to 0-10 volt analog signal) and converts t..

$179.00

DMX 0-10 Volt Analog Converter 19" 1RU Rack Mount

DMX 0-10 Volt Analog Converter 19" 1RU Rack Mount

The DX10Vr is a DMX to 0-10 volt analog converter (other voltages available) in a 19" 1RU rackmount ..

$439.00

DMX Channel Reassign Display Module

DMX Channel Reassign Display Module

The DCRD-PCB is a DMX input channel reassignment module. Reassigns the DMX start channel of a fixtur..

$99.00

DMX 0-10 Volt Analog Converter PCB with Relay Control

DMX 0-10 Volt Analog Converter PCB with Relay Control

The DX10V-RL is a DMX to 10 volt converter with simultaneous relay switching control. This functiona..

$349.00

DMX 0-10 Volt Analog Converter PCB with Power Relay Control

DMX 0-10 Volt Analog Converter PCB with Power Relay Control

The DX10V-PRL is a DMX to 10 volt converter with simultaneous power relay switching control. This fu..

$425.00

DMX Relay Driver w/ 0-10V Option

DMX Relay Driver w/ 0-10V Option

NEW - Now Available! NEW - DXRL is a DMX 512 4 (or 8) channel relay controller with optional 0-10..

$289.00