DX10V USER GUIDE pdf
DX10V-SG SWITCH TO GROUND FUNCTION DIAGRAM [pdf]
DX10V-SG SWITCH TO GROUND CONNECTION DIAGRAM [pdf]
DMX10V DRILL TEMPLATE AND WIRING DIAGRAM [pdf]
DMX512 CHANNEL ASSIGNMENT TABLE [pdf]

DMX CONTROL WARNING: NEVER use DMX data devices where human safety must be maintained.
NEVER use DMX data devices for pyrotechnics or similar controls.
Manufacturer: ELM Video Technology
Brand: ELM Video Technology
Model: DX10V-SG-PCB
Name: DMX to 0-10 Volt Analog Converter Switch Relay Driver
MPN: DX10V-8-SG-PCB
UL Listing: Pre populated PCB
Dimensions: 1.3" Length x 3.4" Width x 1.42" Height (including standoffs)
Condition: New
PCB Mounted Fuse: SMT 750mA
Power Input: +12VDC apx 200mA
Number of Outputs: 8 (optional 4)
Voltage Output: 0~10VDC each, (500 ohm minimum load)
Source Current Output: 20mA Max
Sink Current Output: 10mA Max
LED status indicator: Fast blink=on-board communications error has occurred, Slow blink=A DMX overrun error has occurred
DATA TYPE: DMX (250Khz)
RDM: No
Weight: 3 oz
Operating temperature: 32°F to 85°F
Storage temperature: 0°F to 120°F
Humidity: Noncondensing

PCB Selectable Features

5" Wire Leads - Pre tinned and installed wire leads
12V 1A Power Supply - Wall style wires tinned
DIN Clips for 35mm Rail - Clips installed on the PCB (no standoffs)
DIN Rail 35mm 8 inch - PCB with DIN clips will mount directly to rail

Select

Inside Access Assembly

External Access Assembly

The DX10V-SG-PCB converts a DMX input to a variable 0 to 10 volt analog output and if the DMX level is apx 5% the 0-10V signal is shorted directly to ground, using a mechanical reed relay. If the connected LED drivers do not turn off the LEDs completely when the DMX level is zero, then this functionality may do so. Our DX10V-PRL-PCB will do the same function as well but requires wiring the 120V power to the respective relay that shuts off the power to the fixture or drivers. Standard unit is equipped with 8 channels, (4 channel PCBs available in lots of 5). See the DMX 0 - 10 Volt Products Page to decide if this function will work for your system. Additional order View 4 output PCBs in lots of 5.

To test if this function will work with an existing installation, set the DMX level to zero. If the LEDs are still illuminated connect the 0-10V pink (or purple) wire to the ground. If the LEDs turn off then this PCB should work. To test uninstalled fixtures or drivers, connect a 10 volt source with a 10K ohm potentiometer to vary the 0-10V input and test dimming the LED. When turned all the way down and the lights are still illuminated, connect the 0-10V pink (or purple) wire to the ground. If the LEDs turn off then this PCB should work.

Control 0-10 volt LED drivers or dimmers, for example, from a DMX lighting board or DMX controller. Each output can source up to 20mA and sink up to 10mA. Each output is assigned to a consecutive DMX channel and will vary from 0 to 10 volts in respect to the corresponding DMX channels' level. The DX10V-SG-PCB unit has 8 channels, (4 channel PCB's available in lots of 5). See the DX10V 0-10 volt full description category page for more information.

The DX10V-PCB is designed to mounted for access to the dip switches and LED's either internal or external of an enclosure. The standoffs are mounted on the bottom of the PCB for installing in an enclosure. If the dip switches and LED's are to be accessible from the exterior of the enclosure then select the faceplate mounting option.