Previous Revisions:

DMX10V USER GUIDE Hardware Rev 6 [pdf]
DMX10V USER GUIDE Revision 2-5 [pdf]

DMX CONTROL WARNING: NEVER use DMX data devices where human safety must be maintained.
NEVER use DMX data devices for pyrotechnics or similar controls.

Manufacturer: ELM Video Technology
Name: DMX 0 to 10 Volt Analog Converter Switch Relay Driver
Description: The DX10V converts a DMX-512 input to a variable 0 to 10 volt analog output.
MPN: DX10V-8-DC3P
Model: DX10V
UL Listings: Power supply, PCB pre populated

CHASSIS: Anodized Aluminum .093" thick RoHS compliant
Internal Fuse: SMT 750mA
Power Input: +12VDC apx 400mA (values apx, some circuits may vary)
4 Channel: no load:64mA full load 145mA
8 Channel: no load 70mA full load 230mA
12 Channel: no load 76mA full load 316mA
16 Channel: no load 82mA full load 402mA
Voltage Output: 0~10VDC, (500 ohm minimum load)
Source Current per Output: 20mA Max each
Sink Current per Output: 10mA Max each
0-10V Output Refresh Rate per Second:
V8.00 - 8 Ch: 1502, 16 Ch: 739, 24 Ch: 506
V7.10 - 4 Ch: 3067, 8 Ch: 1512, 16 Ch: 746
V7.00 - 4 Ch: 820, 8 Ch: 400, 16 Ch: 204
V6 & Earlier - 4 Ch: 1162, 8 Ch: 571, 12 Ch: 384, 16 Ch: 285
DATA TYPE: DMX (250Khz)
RDM: No
Data Input: 5 (or 3) pin female XLR, [Pin 1 Not connected, Pin 2Data -, Pin 3 Data +]
Data Loop Output: (If equipped) 5 (or 3) pin female XLR, [Pin 1 Looped from pin 1 of input XLR, Pin 2Data -, Pin 3 Data +]
Dimensions: 3.7 x 6.7 x 2.1 inches
Weight: 1.5 pounds
Operating temperature: 32°F to 100°F
Storage temperature: 0°F to 120°F
Humidity: Noncondensing
Refresh Rate Per Second: 4 Ch's = 1162, 8 Ch's = 571, 12 Ch's = 384, 16 Ch's = 285 (amount of times per second the outputs are updated)
Output Connections: detachable 9 pin screw terminal
External Power Supply: +12VDC wall mount
Voltage Input: 100 ~ 132 (or 240) VAC
Current Output: 1 Amps
Power: 12 Watts
Polarization: Positive Center
Female Plug: Locking Barrel Plug, 2.1mm I.D. x 5.5mm O.D. x 12mm

3 or 5 pin XLR or Ethercon connectors - 1, 2, or 3 Universes per EtherCon (See: EtherCon Pinouts)
Equipped with a single DMX input, optionally add a loop thru with 3 or 5 XLR connectors (terminate if unused)
Equipped with 8 outputs, optionally add an additional 8 or 16 outputs (for a total outputs of 16 or 24). Or an 8 channel with Switch to Ground function. Uses reed relay's to short the 0-10V output to ground when the respective DMX level is below 5%. For more information see the DX10V-SG-PCB page.
Mounting flanges - allows the unit to be counter top, under counter, or wall mounted

The DX10V converts/decodes a DMX-512 input to a variable 0 to 10 volt analog output. Control 0-10 volt LED drivers or dimmers, for example, from a DMX lighting board or DMX controller. Also has a 'switch' option for controlling solid state relay's (SSR). Each output can source up to 20mA and sink up to 10mA. Each output is assigned to a consecutive DMX channel and will vary from 0 to 10 volts in respect to the corresponding DMX channels' level. Standard unit has 8 channels, available with 16 channels. Includes power supply. See the DX10V 0-10 volt full description category page for more information. Note: If custom output voltages are required, most can be preset, for example 0-5 volts, 0-20 volts, 0-24 volts etc-contact us for custom voltages.

EXPAND