DMX CONTROL WARNING: NEVER use DMX data devices where human safety must be maintained. NEVER use DMX data devices for pyrotechnics or similar controls.


MANUFACTURER:   ELM Video Technology

NAME:             DMX to PWM Controller and/or Driver

DESCRIPTION:     The DPM8 converts DMX to variable duty cycle PWM (Pulse Width Modulation)

MPN:     DPM8-DC3P

MODEL:      DPM8

CHASSIS:     Anodized Aluminum .093" thick RoHS compliant

PCB FUSE:     SMT 2A

PWM OUT FUSE:     Inline 2A (installed if unit has a 12V output)

POWER INPUT:     +12VDC 80mA + sum of PWM outputs

PWM VOLT/AMP:     Ground Drive Unit outputs a ground signal for the duration of the respective duty cycle at a max of 150mA. If an alternate external power supply max voltage 30VDC.

            3.4V Control Voltage Unit outputs a +3.4 volt signal for the duration of the respective duty cycle at a max of 5mA

DATA TYPE:             DMX 512 (250Khz)

DATA INPUT:      3 (or 5) pin male XLR  [Pin 1 Not connected, Pin 2 Data -, Pin 3 Data +]

DATA LOOP OUT:   (If equipped) 3 (or 5) pin female XLR  [Pin 1 Looped from pin 1 of input XLR, Pin 2 Data -, Pin 3 Data +]

CHASSIS GND:     Input power connector negative shorts to chassis

RDM CAPABLE:     No

DIMENSIONS:     3.7 x 6.7 x 2.1 inches

WEIGHT:     1.5 pounds 

OPERATING TEMP:32°F to 100°F

HUMIDITY:     Non condensing

OUTPUT CONN.:     9 pin terminal block

POWER SUPPLY:     +12VDC wall mount

    Voltage Input:     100 ~ 132 (or 240) VAC

    Current Output:  1A or 2A depending on unit/options

    Polarization:     Positive Center

    Output Conn.:     12V unit - Locking Barrel Plug, 2.1mm I.D. x 5.5mm O.D. x 9.5mm

            5V unit - Locking Barrel Plug, 2.5mm I.D. x 5.5mm O.D. x 9.5mm

  • 3 or 5 pin XLR connectors
  • Mounting flanges - allows the unit to be counter top, under counter, or wall mounted


  • PWM OUTPUT OPTIONS:

    • Ground Drive: a higher current drive that can be used to drive SSRs (solid state relays) or LEDs. The connected equipment can use the 12 volt unit output or an external power supply can be used up to 30VDC
    • 3.4V Control Voltage: is a set voltage with up to 5mA per output, providing a control voltage only for PWM controlled drivers such as PWM LED Drivers



    The DPM8 is a next generation new design DMX to 8 channel PWM (Pulse Width Modulation) controller driver with a wide range of tunable frequencies that can be user programmed. Need PWM to vary the frequency of LED's to eliminate TV strobing? The DPM8 will allow up to 4 different frequencies to be tuned (2 independent PWM outputs per frequency). The standard frequency range is from 123hz - 31.25Khz or in the Hi Speed option the range is tunable from 980hz to 250Khz. Each ground drive output can drive up to 150mA at 12VDC (30VDC Max). Designed to control SSR (Solid State Relays) that could then directly power high power LED fixtures, or any PWM circuits that need DMX to PWM control. OR 

    choose the positive control voltage version that can provide a low current control voltage output. 


    FEATURES INCLUDE:

    • 4 programmable tunable frequency settings
    • 8 Independent outputs
    • Choose either ground drive OR control voltage functionality
    • Programmable stand alone (no DMX) outputs
    • Compatible with all ELM Video Technology's DMX products
    • Drive solid state relays or any PWM controlled input
    • LED indicators for: Power, Data/Status, and 8 Outputs



    DMX to 8 PWM Controller Driver

    • $349.00


    • 5 or more $340.00
    • 10 or more $330.00

    Available Options


    Related Products

    DMX to 8 PWM Controller Driver PCB

    DMX to 8 PWM Controller Driver PCB

    The DPM8-PCB is a next generation new design DMX to 8 channel PWM (Pulse Width Modulation) controlle..

    $179.00

    Tags: dmx, 512, dpm8, pulse, width, modulation, pwm, controller, frequency, tunable, tune driver, pcb